产品分类

Categories

您的位置:首页 -> 苏州全自动超声波清洗机生产厂家

苏州全自动超声波清洗机生产厂家


苏州全自动超声波清洗机生产厂家

设备名称:苏州全自动超声波清洗机生产厂家

  • 设备名称: 苏州全自动超声波清洗机生产厂家
  • 设备型号: XQ-8089SGR
  • 清洗对象: 五金加工件、电子配件、晶体半导体、汽车发动机等
  • 产品类型: 机械臂全自动
  • 产品价格: 面议或电话联系:136-8951-4505

苏州全自动超声波清洗机生产厂家-深圳心齐苏州全自动超声波清洗机生产厂家-深圳心齐供应

深圳心齐全自动超声波清洗机厂家的操作流程


1、準備好超聲波清潔機,倒入清水。打開電源開關。按照箭頭指示擰啟動開關,待指示燈亮起表示超聲波清潔機已啟動,即可進行清潔。


2、揭开盖子,向大家展示内部的构造。实际上,里面只是一个凹槽,您可以将需要清洗的物品放入其中。在放入凹槽时,请务必确保工业全自动超声波清洗机容器内装满水,务必装满水,否则可能无法洗净。


3、操作步骤如下:启动溢流管排放阀,将清洗液或水注入清洗池,直至清洗液开始溢出(建议使用刮刀之类的工具沿溢出口方向刮除漂浮油以促进其快速流出),保持溢流管排放阀保持关闭,以防止意外溢出导致地面污染。


4、全自动超声波清洗机设备的电源和加热器电源必须配置良好的接地设备。严格禁止在超声波清洗机没有清洗液的情况下启动,即在清洗槽中未加入足够的清洗液前不得开启超声波开关。带有加热装置的清洗设备在没有液体时不得打开加热开关。


5、定期启动全自动超声波清洗机器的油泵,每次至少运转10分钟以上。使用完清洗机后,请将其盖上罩子,做好防尘和防潮工作。


6、心齐机械臂式全自动超声波清洗机工作的第一步是开启电源并安装好进水管、出水管以及电路所需连接的部件。




Shenzhen heart complete automatic ultrasonic cleaning machine manufacturer's operating procedures


1、Prepare the ultrasonic cleaning machine, pour in water. Turn on the power switch. Screw the start switch according to the arrow instructions, and wait for the indicator light to come on to indicate that the ultrasonic cleaning machine has been activated, you can clean.


2. Uncover the lid to show you the inner structure. In fact, the inside is just a recess into which you can put the items that need to be cleaned. When you put in the recess, please make sure that the container of the industrial automatic ultrasonic cleaner is full of water. Make sure it is full of water, otherwise you may not be able to wash it.


3, the operating steps are as follows: start the overflow pipe discharge valve, the cleaning fluid or water into the cleaning pool, until the cleaning fluid began to overflow (it is recommended to use a scraper or other tools along the direction of the overflow port to scrape the floating oil to promote its rapid outflow), to keep the overflow pipe discharge valve to keep it closed, in order to prevent accidental overflow resulting in ground contamination.


4, automatic ultrasonic cleaning machine equipment power supply and heater power supply must be configured with good grounding equipment. Strictly prohibit the ultrasonic cleaning machine without cleaning fluid to start, that is, in the cleaning tank is not added to the sufficient cleaning fluid shall not be turned on before the ultrasonic switch. Cleaning equipment with a heating device in the absence of liquid may not open the heating switch.


5, regularly start the automatic ultrasonic cleaning machine oil pump, each time at least 10 minutes of operation. After using the cleaning machine, please cover it with a cover to prevent dust and moisture.


6, heart Qi mechanical arm type automatic ultrasonic cleaning machine work the first step is to turn on the power supply and install the inlet pipe, outlet pipe and the circuit required to connect the parts.

首 页 | 产品中心 | 成功案例 | 资质认证 | 合作伙伴 | 新闻中心 | 关于心齐 | 人才招聘 | 企业文化 | 在线留言 | 联系我们
关闭
点击这里给我发消息
客服一
点击这里给我发消息
客服二
点击这里给我发消息
客服三
点击这里给我发消息
客服四